Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
laserparameters [2012/05/23 16:57] – [Table] brunnelaserparameters [2012/07/20 19:16] (current) – [Table] brunne
Line 12: Line 12:
 |  Cr/Au on glass wafer  |      cut           500 nm | 100%   | 800 mm/s  |      70 kHz      | Single line                                                                22                            | Electrical circuits on glass                                         | Krausse             | |  Cr/Au on glass wafer  |      cut           500 nm | 100%   | 800 mm/s  |      70 kHz      | Single line                                                                22                            | Electrical circuits on glass                                         | Krausse             |
 |  Cr/Au on glass wafer  |     hatch      |     500 nm | 100%   | 500 mm/s  |      20 kHz      | hatch StefanK_CrAu                              |                            10                            | Electrical circuits on glass                                         | Krausse             | |  Cr/Au on glass wafer  |     hatch      |     500 nm | 100%   | 500 mm/s  |      20 kHz      | hatch StefanK_CrAu                              |                            10                            | Electrical circuits on glass                                         | Krausse             |
-     spring band steel     hatch      |     150 µm | 100%   20mm/        20 kHz      8 hatches, 45° inc. 8µm spacing, no  margin                                20                            Hole                                                                 Wiedenmann          +        Pyrex           cut by hatch  |     500 µm |                                                                                                                                                                                                                 Spengler            
-|      Steel sheet            cut           120 µm | 100%   | 10mm/   | 20 kHz           | 3 parallel lines, 60 µm wide                    | 15                                                       | "fast" cut, 0.21 mm/s                                                | Brunne              |+ 
 + 
  
  
Line 31: Line 33:
 \\ \\
 ===Polymers=== ===Polymers===
-^          Material           ^ hatch or cut?  ^ thickness  ^ Power  ^ Velocity   ^ Pulse frequency  ^ hatch parameters or parallel lines           ^ Repetitions  ^ Project or comments            ^        Name        ^ +^          Material           ^ hatch or cut?  ^ thickness                     ^ Power  ^ Velocity   ^ Pulse frequency  ^ hatch parameters or parallel lines           ^ Repetitions  ^ Project or comments             ^        Name        ^ 
-|           Kapton            |      cut           120 µm | 100%   | 170 mm/s        25 kHz      | single line                                  |      18      |               --               | Brunne, Gleißner   | +|           Kapton            |      cut                              120 µm | 100%   | 170 mm/s        25 kHz      | single line                                  |      18      |               --                | Brunne, Gleißner   | 
-|           Kapton            |      cut            50 µm | 100%   | 170 mm/s        25 kHz      | single line                                  |      10      | Inkjet printed AgNP            | Bollgrün           | +|           Kapton            |      cut                               50 µm | 100%   | 170 mm/s        25 kHz      | single line                                  |      10      | Inkjet printed AgNP             | Bollgrün           | 
-|            SU-8                 hatch      |   10 µm    | 70%    | 950 mm/s        48 kHz      | 2 hatches, 90° inc., 5 µm spacing            |      1       | MAXWELL                        | Schöttler, Brunne +|            SU-8                 hatch      |             10 µm             | 70%    | 950 mm/s        48 kHz      | 2 hatches, 90° inc., 5 µm spacing            |      1       | MAXWELL                         | Schöttler, Brunne 
-|     Paper-base plastics          cut          1 mm    |  100%  |  75 mm/s        20 kHz      | 5 lines, 125 µm wide                              25      | 3D Energy Harvester            | Lausecker          | +|     Paper-base plastics          cut                   1 mm              |  100%  |  75 mm/s        20 kHz      | 5 lines, 125 µm wide                              25      | 3D Energy Harvester             | Lausecker          | 
-|  Paper-base plastics (FR2)  |      cut          1 mm    |  100%  |  75 mm/s        20 kHz      | 5 lines, 125 µm spacing, defocus corrected!  |      16      | MAXWELL                        | Brunne             | +|  Paper-base plastics (FR2)  |      cut                   1 mm              |  100%  |  75 mm/s        20 kHz      | 5 lines, 125 µm spacing, defocus corrected!  |      16      | MAXWELL                         | Brunne             | 
-|  Paper-base plastics (FR2)  |     hatch      |   600 µm   |  100%  |  100 mm/s  |      20 kHz      | 20µm spacing, 4 hatches                      |      3       | MAXWELL                        | Brunne             | +|  Paper-base plastics (FR2)  |     hatch      |            635 µm             |  100%  |  100 mm/s  |      20 kHz      | 20µm spacing, 4 hatches                      |      3       | MAXWELL                         | Brunne             | 
-|  unknown katheter polymer       hatch      |   180 µm   |  100%  |  800 mm/s  |      20 kHz      | 4 hatches, 45° inc., 10 µm spacing                2       | Katheter (hole for capacitor)  | Wiedenmann         |+|     Paper-base plastics         hatch      |              235              |  100%  |  150 mm/s  |      20 kHz      | 20µm spacing, 4 hatches                      |      2       | MAXWELL                         | Brunne             | 
 +|  unknown katheter polymer       hatch      |            180 µm             |  100%  |  800 mm/s  |      20 kHz      | 4 hatches, 45° inc., 10 µm spacing                2       | Katheter (hole for capacitor)   | Wiedenmann         | 
 +|            Mylar            |      cut                  350 µm              100%  |  100 mm/s  |      25 kHz      | single line                                  |      18      | for small parts insert 1s wait  | Wapler             | 
 +|  Double-sided sticky foil        cut        90 µm Tape (10 µm adhesive)  |        |            |      20 kHz      | single line                                  |      2       | Transformer                     | Spengler           | 
 +|            PDMS                  cut                   550µm             | 100%   | 50 mm/s    |      20 kHz      | 250µm trench, 10 parallel lines              |      15      | MAXWELL                         | Brunne             | 
 + 
 + 
 + 
 + 
 +\\ 
 +===Metals=== 
 +^  Material   ^hatch or cut?^thickness^Power^Velocity^Pulse frequency^hatch parameters or parallel lines     ^Repetitions^Project or comments^   Name   ^ 
 +|Aluminum foil|cut|18µm|100%|10mm/s|20kHz|--|3|Microlev - cut through after 1 or 2 rep.|Brunne| 
 +|      spring band steel |     hatch      |     150 µm | 100%   | 20mm/   |      20 kHz      | 8 hatches, 45° inc. 8µm spacing, no  margin                                20                            | Hole                                                                 | Wiedenmann          | 
 +|      Steel sheet            cut           120 µm | 100%   | 10mm/   | 20 kHz           | 3 parallel lines, 60 µm wide                    | 15                                                       | "fast" cut, 0.21 mm/s                                                | Brunne              | 
 + 
  
 \\ \\

QR Code
QR Code laserparameters (generated for current page)