| Both sides previous revisionPrevious revisionNext revision | Previous revision |
| laserparameters [2012/07/16 14:23] – brunne | laserparameters [2012/07/20 19:16] (current) – [Table] brunne |
|---|
| | Cr/Au on glass wafer | cut | 500 nm | 100% | 800 mm/s | 70 kHz | Single line | 22 | Electrical circuits on glass | Krausse | | | Cr/Au on glass wafer | cut | 500 nm | 100% | 800 mm/s | 70 kHz | Single line | 22 | Electrical circuits on glass | Krausse | |
| | Cr/Au on glass wafer | hatch | 500 nm | 100% | 500 mm/s | 20 kHz | hatch StefanK_CrAu | 10 | Electrical circuits on glass | Krausse | | | Cr/Au on glass wafer | hatch | 500 nm | 100% | 500 mm/s | 20 kHz | hatch StefanK_CrAu | 10 | Electrical circuits on glass | Krausse | |
| | spring band steel | hatch | 150 µm | 100% | 20mm/s | 20 kHz | 8 hatches, 45° inc. 8µm spacing, no margin | 20 | Hole | Wiedenmann | | |
| | Steel sheet | cut | 120 µm | 100% | 10mm/s | 20 kHz | 3 parallel lines, 60 µm wide | 15 | "fast" cut, 0.21 mm/s | Brunne | | |
| | Pyrex | cut by hatch | 500 µm | | | | | | | Spengler | | | Pyrex | cut by hatch | 500 µm | | | | | | | Spengler | |
| |
| | Mylar | cut | 350 µm | 100% | 100 mm/s | 25 kHz | single line | 18 | for small parts insert 1s wait | Wapler | | | Mylar | cut | 350 µm | 100% | 100 mm/s | 25 kHz | single line | 18 | for small parts insert 1s wait | Wapler | |
| | Double-sided sticky foil | cut | 90 µm Tape (10 µm adhesive) | | | 20 kHz | single line | 2 | Transformer | Spengler | | | Double-sided sticky foil | cut | 90 µm Tape (10 µm adhesive) | | | 20 kHz | single line | 2 | Transformer | Spengler | |
| | | PDMS | cut | 550µm | 100% | 50 mm/s | 20 kHz | 250µm trench, 10 parallel lines | 15 | MAXWELL | Brunne | |
| | |
| |
| |
| ^ Material ^hatch or cut?^thickness^Power^Velocity^Pulse frequency^hatch parameters or parallel lines ^Repetitions^Project or comments^ Name ^ | ^ Material ^hatch or cut?^thickness^Power^Velocity^Pulse frequency^hatch parameters or parallel lines ^Repetitions^Project or comments^ Name ^ |
| |Aluminum foil|cut|18µm|100%|10mm/s|20kHz|--|3|Microlev - cut through after 1 or 2 rep.|Brunne| | |Aluminum foil|cut|18µm|100%|10mm/s|20kHz|--|3|Microlev - cut through after 1 or 2 rep.|Brunne| |
| | | spring band steel | hatch | 150 µm | 100% | 20mm/s | 20 kHz | 8 hatches, 45° inc. 8µm spacing, no margin | 20 | Hole | Wiedenmann | |
| | | Steel sheet | cut | 120 µm | 100% | 10mm/s | 20 kHz | 3 parallel lines, 60 µm wide | 15 | "fast" cut, 0.21 mm/s | Brunne | |
| |
| |
